How to get it right: Parapet walls

Blog Post
Picture of a parapet wall - getting parapet walls right by LABC

Parapet walls behave differently to conventional cavity walls because of their location at the very top of a building where both skins of the parapet are outer skins, and as such are exposed to moisture.

Traditionally constructed parapet walls can become saturated with rain and are also subject to extremes of heat and cold, leading to expansion of the masonry.

When this occurs the damp proof course (DPC) course in a parapet offers the line of least resistance and acts as a slip plane, so movement at DPC level in the outer and inner skins is common.

Diagram showing parapet wallWhere the amount of expansion is not fully compensated by contraction, progressive movement over the years will occur. This is mainly as a result of ‘ratcheting’ (where the expansion movement is not fully matched by the retraction movement, and masonry above and below the DPC progressively moves out of alignment).  

This is easily identified first by witness lines and eventually by horizontal cracking along the courses in which the parapet DPC has been supported, as you can see in the photo.

A spokesman for tray manufacturer Cavity Trays of Yeovil explained:

“Originally the British Standard showed an inward stepping DPC rather than an outward one and at first, parapet walls built to that detail functioned correctly.

“But it only takes a few years before parapet cracking occurs, and eventually water will permeate the outer skin along the DPC bedding joint and track inwardly on the underside of that inward stepped DPC.

“As soon as that tracking reaches the inner skin, the damp problem becomes visible.”

Cavity Trays of Yeovil explains that their approach was the opposite. They designed an outward stepping arrangement - the concept subsequently adopted within the latest British Standard.

However, an alternative approach using a preformed parapet ‘Cavitray’ that is self-supporting and only needs to be built into one skin, offers lots of advantages. The requisite outward stepping profile is achieved but the opposite masonry skin can remain uninterrupted and as such, the structural integrity is significantly improved. The parapet tray is called Type P.

Parapet walls need not be problematic. The right specification ensures a correctly protected structure and one in which the structural continuity isn’t hindered by DPC slip-planes. 

Further information

http://www.cavitytrays.co.uk/damp-proofing/view/1/32/1/type-p-cavitray

http://www.cavitytrays.co.uk/pdf/32-Type-P.pdf

Please Note: Every care was taken to ensure the information was correct at the time of publication. Any written guidance provided does not replace the user’s professional judgement. It is the responsibility of the dutyholder or person carrying out the work to ensure compliance with relevant building regulations or applicable technical standards.

Comments

(No subject)

Submitted 6 years 2 months ago

I have a 9 inch parapet wall which extends 400mm above one of two garage rooves. The other garage roof is 700mm below the coping. I plan to fit a superior coping stone with water channels and 280 mm wide. The 9 inch wall has no cavity to speak of and flashing is inserted above each roof by 2 courses. I am concerned that the new coping is insufficient, ie wind blown falling water from the drip channel of the coping. the wall exhibit significant dampness after heavy rain. I would welcome any advice you can offer.
Many thanks Ted Nelson

(No subject)

Submitted 6 years 2 months ago

the relationship with cavity insulation needs to be dealt with as the position of cavity flashings may affect what insulation goes where - perhaps above and below for thermal continuity etc?

Webmaster note

Submitted 6 years 2 months ago

All comments posted at an earlier date to this one have been transferred from our old website.

Parapet Wall Cold Flat Roof

Submitted 4 years 6 months ago

Due to planning we have a relatively low parapet wall which has meant we have to use a cold flat roof as the takes up less than a warm flat roof. Traditional masonry with coping stone.

Any idea how we can ventilate this?
Any details?

Thank you
Joe

Reply

Submitted 4 years 6 months ago

Hello Joe

Many thanks for your comment.

You'll need to engage the services of a professional agent with experience of the roof design you intend to use on your project. Unfortunately we aren't able to offer private design services.

Regards
Barry, LABC

Parapet Copings

Submitted 2 years 11 months ago

From experience great care must be exercised to check the forming of the drip section to the coping. As the quality of this varies greatly, drips that are not cleanly formed and do not have the required overhang from the masonry will allow water to track back under the DPC breaking the bond and allowing water into the cavity.

Ychwanegu sylw newydd

This question is for testing whether or not you are a human visitor and to prevent automated spam submissions.

Sign up to the building bulletin newsletter

Over 48,000 construction professionals have already signed up for the LABC Building Bulletin.



Join them and receive useful tips, practical technical information and industry news by email once every 6 weeks.



Subscribe to the Building Bulletin